آموزش نحوه ساخت Bootable CD برای Windows XP

[TAHA]

سلام

در این مقاله بصورت تصویری نحوه Bootable کردن CD را تقدیم حضورتان می کنم.

برای اینکار به دو نرم افزار احتیاج داریم:
1- نرم افزار IsoBuster جهت استخراج نسخه Image سیستم عامل از Setup CD ویندوز (از اینجا دانلود کنید (http://www.satsat3.com/showthread.php?t=178992))
2- نرم افزار Nero Burning Rom (ورژن 5.5.9.0 یا بالاتر)

الف) استخراج فایل Image از CD ویندوز
1- ابتدا CD ویندوز را در درایو گذاشته و نرم افزار IsoBuster را اجرا کنید.
2- در قسمت سمت چپ پنجره IsoBuster گزینه Bootable CD را انتخاب کنید.
3- در قسمت راست پنجره روی Microsoft Corporation.img راست کلیک کرده و گزینه Extract Microsoft Corporation.img را انتخاب کنید.
http://pnu-club.com/imported/mising.jpg
4- محلی برای ذخیره فایل تعیین کنید (در اینجا بعنوان مثال D:\XP-CD در نظر گرفته شده)

ب) قرار دادن فایل Image در Boot Sector سی دی خام
- Nero را اجرا کنید.
- در پنجره NewCompliation گزینه ( CD-ROM (Boot را انتخاب کنید.
- گزینه Image File را انتخاب و با فشار کلید Browse فایل ساخته شده مرحله قبل را تعیین کنید.
- Enable expert setting را فعال کرده، Kind of Emulation را روی No تنظیم کنید و Number of loaded sectors را روی عدد 4 تنظیم کنید.
http://pnu-club.com/imported/mising.jpg
- سربرگ ISO را مطابق شکل زیر تنظیم کنید:
http://www.pnu-club.com/imported/mising.jpg
- توصیه می کنم در سربرگ Label حتماً از برچسب های استاندارد Windows استفاده نمایید:
1- برای ویندوز XP Professional برچسب WXPCCP_EN
2- برای ویندوز XP Home برچسب WXHCCP_EN
3- برای ویندوز XP Professional OEM برچسب WXPOEM_EN
4- برای ویندوز XP Home OEM برچسب WXHOEM_EN
http://www.pnu-club.com/imported/mising.jpg

- کلید New را فشار داده و فایل Image را که در فولدر D:\XP-CD ذخیره کرده بودید را باز کنید
- ساخت Boot Sector به پایان رسیده، فایلهای مورد نیاز را به پنجره ISO1 دراگ کرده و CD را Burn کنید.


http://www.pnu-club.com/imported/mising.jpg

[cho0bin]

سلام

در این مقاله بصورت تصویری نحوه bootable کردن cd را تقدیم حضورتان می کنم.

برای اینکار به دو نرم افزار احتیاج داریم:
1- نرم افزار isobuster جهت استخراج نسخه image سیستم عامل از setup cd ویندوز (از اینجا دانلود کنید (http://pnu-club.com/redirector.php?url=http%3a%2f%2fwww.satsat3.com%2f showthread.php%3ft%3d178992))
2- نرم افزار nero burning rom (ورژن 5.5.9.0 یا بالاتر)

الف) استخراج فایل image از cd ویندوز
1- ابتدا cd ویندوز را در درایو گذاشته و نرم افزار isobuster را اجرا کنید.
2- در قسمت سمت چپ پنجره isobuster گزینه bootable cd را انتخاب کنید.
3- در قسمت راست پنجره روی microsoft corporation.img راست کلیک کرده و گزینه extract microsoft corporation.img را انتخاب کنید.
http://pnu-club.com/imported/mising.jpg
4- محلی برای ذخیره فایل تعیین کنید (در اینجا بعنوان مثال d:\xp-cd در نظر گرفته شده)

ب) قرار دادن فایل image در boot sector سی دی خام
- nero را اجرا کنید.
- در پنجره newcompliation گزینه ( cd-rom (boot را انتخاب کنید.
- گزینه image file را انتخاب و با فشار کلید browse فایل ساخته شده مرحله قبل را تعیین کنید.
- enable expert setting را فعال کرده، kind of emulation را روی no تنظیم کنید و number of loaded sectors را روی عدد 4 تنظیم کنید.
http://pnu-club.com/imported/mising.jpg
- سربرگ iso را مطابق شکل زیر تنظیم کنید:
http://pnu-club.com/imported/mising.jpg
- توصیه می کنم در سربرگ label حتماً از برچسب های استاندارد windows استفاده نمایید:
1- برای ویندوز xp professional برچسب wxpccp_en
2- برای ویندوز xp home برچسب wxhccp_en
3- برای ویندوز xp professional oem برچسب wxpoem_en
4- برای ویندوز xp home oem برچسب wxhoem_en
http://pnu-club.com/imported/mising.jpg

- کلید new را فشار داده و فایل image را که در فولدر d:\xp-cd ذخیره کرده بودید را باز کنید
- ساخت boot sector به پایان رسیده، فایلهای مورد نیاز را به پنجره iso1 دراگ کرده و cd را burn کنید.


http://pnu-club.com/imported/mising.jpg

سلم
ميشه يه آموزش تصويري درست كنيد
كارم خيلي گيره
ممنون ميشم

[Borna66]

سلم
ميشه يه آموزش تصويري درست كنيد
كارم خيلي گيره
ممنون ميشم
اينم يك آموزش ساده تصويري كه البته زبان اصلي هست ولي روان هست




Making a XP Bootable CD

The following are the instructions for making a bootable XP CD using Nero


To begin, download the Microsoft Corporatiion.img (http://www.onecomputerguy.com/software/Microsoft%20Corporation.img) file and remember the location where you download it to your computer
1. Start Nero 2.
Double click on CD-ROM (boot) 3. Check Image File 4. Click on the Browse button, File of Type - All Files, Select the Image file 5. Keep the Nero Boot-Loader 07C0 6. Load Segment - 07C0 7. Number of loaded sectors - 4 8. Make the screen look like the following graphic http://pnu-club.com/imported/2010/07/796.jpg 8. Click on the ISO tab 9. Configure it to match the following graphic http://pnu-club.com/imported/2010/07/798.jpg 10. Click on the LABEL tab 11. You don't need to but here are the default labels for the different versions of XP:

Windows XP Professional: WXPCCP_EN
Windows XP Home: WXHCCP_EN
Windows XP Professional OEM: WXPOEM_EN
Windows XP Home OEM: WXHOEM_EN

12. Click on the New button 13. Select your XP Source files and drag to the window on the left http://pnu-club.com/imported/2010/07/799.jpg 14. Make your bootable XP CD.


Copying the Source Files

1. If your WindowsXP source files are already on the computer's hard drive you can skip this section. 2. Insert your WindowsXP CD 3. If prompted, do not install WindowsXP 4. Create a directory on the hard drive and copy the entire contents of the CD to that directory 5. For example, use c:\winxp


Performing the SlipStream

1. Given the previous examples, go to the c:\xp_sp2\i386\update directory 2. Run:
update.exe -S:c:\winxp 3. When it is finished, you will see the message The Integrated install has completed successfully 4. You can now copy the c:\winxp directory to a CD or other location. 5. If you need to make a bootable CD ROM, there are other locations on the Internet with good detailed instructions.

[Borna66]

اينم يك آموزش ديگر

Create A Bootable Windows XP Installation CD Slipstreamed with SP1


Information on creating a Bootable XP CD Slipstreamed with SP2 is located here (http://www.theeldergeek.com/slipstreamed_xpsp2_cd.htm).

Now that Service Pack 1http://www.pnu-club.com/imported/2009/03/230.gif (http://www.theeldergeek.com/slipstreamed_xpsp1_cd.htm#) (SP1) has been released for Windows XP a lot of people have been updating their systems. In fact, a lot have been doing clean installations followed immediately by applying SP1 to eliminate much of the garbage that has collected over the past year of using XP. There really isn't a downside to reformatting and doing a clean install, but if there was one I suppose it could be that the installation of SP1 might be quite time consuming, especially if you do it through Windows Update. However, there is a way to reduce this time expenditure.

If you fall into the category of users that frequently reformat their systems and clean install XP from the CD then creating a slipstreamed version of XP/SP1 can be a huge time saver. You invest the time once and then on subsequent reinstalls you avoid bringing XP up to SP1 speed via Windows Update downloads and installations. You will still have to get the post SP1 updates from Windows Update, but the time saved will still be worthwhile.
What Is A Slipstreamed Installation CD?


Think of your installation CD as providing a stream of data to your computer to set up the operating system. On the day XP was released the data stream was up to date and current. As months have gone by, upgrades and fixes have been issued to make your system more stable and secure. SP1 is a compilation of those updates and fixes. Slipstreaming 'slips' these new bits of data from SP1 into the 'stream' of data that the original CD provided, effectively merging the two into one XP Installation CD ROM. A slipstreamed CD is used just like any other Windows installation CD. Without a slipstreamed CD when you go to Windows Update you might find 15 - 20 Critical Updates are needed. The screen capture below was taken immediately after an installation of XP Pro made from a slipstreamed XP/SP1 Installation CD created from the instructions contained in this article. As you can see, no Critical Updates or Service Packs are needed due to slipstreaming SP1 into XP.

http://pnu-club.com/imported/mising.jpg
Creating A Slipstreamed XP/SP1 Installation CD

Gathering the Needed Parts and Pieces


There are a few essential items necessary to successfully create the slipstreamed CD. You will need:



The original Windows XP installation CD ROM - The new CD can be created from either the Home or Professional version of Windows XP. If your computer came with an OEM version of XP it can also be used.

Windows XP Service Packhttp://www.pnu-club.com/imported/2009/03/230.gif (http://www.theeldergeek.com/slipstreamed_xpsp1_cd.htm#) 1 - It will be necessary to either download SP1 or obtain it on CD. To slipstream, you need the full SP1 which is a 133MB download available here (http://www.microsoft.com/windowsxp/downloads/updates/sp1/network.mspx).

CD Creation Software - A burning program for your CD-R or CD-RW drive that allows creating bootable CD's. Unfortunately, while XP does come with the capability to burn CD's built in, the software it uses is not suitable for this task. Since the majority of my readers here seem to be using Roxio Easy CD Creator I've used it in the tutorial, but the instructions can be adapted to other burning software.

ISO Buster - Used to extract the boot loader image file for the CD. It's a free downloadhttp://www.pnu-club.com/imported/2009/03/230.gif (http://www.theeldergeek.com/slipstreamed_xpsp1_cd.htm#) here (http://www.smart-projects.net/isobuster/).


Note: These instructions passed compatibility testing with Service Pack 1a released on February 5, 2003.
Building Directories

The first step is to build a directory structure to hold the files that will be used in the CD creation process. It's a simple structure, requiring nothing more than a main folder with three sub-folders. It doesn't matter what names you use for your structure or where you locate them on your hard drive, but most users find drive C the easiest. I used the structure shown below, located on Drive C. Create whatever folders you are comfortable with or use the ones below if you want to cut and paste commands later in the tutorial. Whatever your choice, it's the relationship between the components that's important, not the naming of the parts.



Main Folder: XP-SS [Located on Drive C]

Sub-Folder: SS-Boot
Sub-Folder: SS-Root
Sub-Folder: SS-XP1




Copying and Extracting Files



The first step is to insert the Windows XP CD and copy the entire contents into the SS-Root folder or the equivalent folder in your structure.

Before copying the XP CD make sure that the system is set to display all hidden and system files to ensure a complete copy of all files on the CD. The settings to control what files are visible are located in Windows Explorer > Tools > Folder Options > View tab. Make sure [Show hidden files and folders] radio button is selected and [Hide protected operating system files] is unchecked.


The second step is to navigate to where you downloaded the Service pack 1 file. If you downloaded SP1 from Microsoft it should be named xpsp1_en_x86.exe. Copy the file to the XP-SS folder and then rename it to xp-sp1.exe after the copy operation completes.

(If you are using the CD of SP1 the files should already be extracted. Copy them into the XP-SS folder)


Use the Run dialogue shown below to extract the contents of the Service Pack to the previously created SS-XP1 folder.


The Run dialogue box is accessed from [Start] [Run]
The command to begin the extraction is: C:\XP-SS\XP-SP1.EXE -U -X:C:\XP-SS\SS-XP1

http://pnu-club.com/imported/mising.jpg



Apply the extracted Service Pack 1 to Windows XP in the SS-Root folder using the [Run] dialogue box.


The Run dialogue box is accessed from [Start] [Run]
The command to apply the Service Pack is: C:\XP-SS\SS-XP1\Update\Update.exe -S:C:\XP-SS\SS-Root

http://pnu-club.com/imported/mising.jpg

As shown below, Service Pack 1 is being integrated into the Windows installation folder.

http://pnu-club.com/imported/mising.jpg

Successful completion of the integration process.

http://pnu-club.com/imported/mising.jpg



In order to make the new CD bootable it's necessary to add the file Microsoft Corporation.img to the folder SS-Boot we created earlier. There are a number of ways to do this but the easiest is to use ISO Buster. With the Windows XP CD in your CD drive, open ISO Buster. Click on Bootable CD in the left pane then right click Microsoft Computing.img in the right pane, finally clicking Extract Microsoft Corporation.img file.


http://pnu-club.com/imported/mising.jpg

Extract the file to the SS-Boot folder previously created or your equivalent.

http://pnu-club.com/imported/mising.jpg

With the preparation out of the way it's time to actually burn the new CD. There are a number of different burning or CD creation programs that can be used to accomplish this task. A large majority of users seem to favor either Easy CD Creator by Roxio or Nero Burning Rom by Ahead Software. This tutorial provides instructions for both programs. The terminology and screens may vary depending on your program choice but the principles remain the same and can be easily adapted no matter what burning software is being used. Choose a link below to complete the XP Slipstreamed CD project.

Windows XP/SP1 Slipstreamed CD - Roxio Easy CD Creator 5.0 Procedure (http://www.theeldergeek.com/slipstream_roxio_procedure.htm)

Windows XP/SP1 Slipstreamed CD - Roxio Easy CD and DVD Creator 6 (http://www.theeldergeek.com/slipstream_roxio6_procedure.htm)
Windows XP/SP1 Slipstreamed CD - Nero Burning Rom Procedure (http://www.theeldergeek.com/slipstream_nero_procedure.htm)